877-878-4060
SHOP ALL PRODUCTS
V

200A, 50mV DC Shunt for Current Monitoring Meters

200A, 50mV DC Shunt for Current Monitoring Meters
200A, 50mV DC Shunt for Current Monitoring Meters
$34.09 List price $41.00

Estimate Shipping
Item code Brand name Model number
GENSHNT200/50 Bogart Engineering MKB-200-50

Bogart Engineering DC Shunt

Bogart Engineering
DC Anmeter Shunt
200 A, 50 mV

Specifications

  • Resistance: "200 Amp at 50 millivolts" or .25 milliohm
  • Physical characteristics: Has plastic base 2.00 x 1.25 inches, with two mounting holes .205 "dia, .875 apart o.c. Overall height 1.75 inches. High current connections are made to two bolts (1/4"-28) which are 1.00" apart

How a Shunt Works

A shunt is necessary in order to measure amps and amp-hours with the TriMetric battery monitor. A shunt is an accurate, very low resistance resistor which is placed "in line" with the wire carrying the current to be measured. With the TriMetric, it is usually placed in the negative wire from the battery bank, such that all the current going into the battery (charging) or out (discharging) must pass through it. Connected in this way it will be set up to monitor "net" amp-hours in and out of the battery. (It also could be placed in series with the negative wire coming from a solar array--or other charging source--in which case it would measure only the solar array current, if that were desired--to show total solar "amp hours" production.) The shunt needs to be placed near the batteries; since these wires carry very high currents the wires from the batteries must be kept short to minimize electrical losses.

Shunt Resistance

When current flows through the shunt, a small voltage is developed across the shunt which is proportional to the current flow. The TriMetric battery monitor accurately measures this very low voltage and converts it to the "amps" reading on the meter. The resistance, which is the ratio between the voltage across the shunt and the current flowing through it, is a constant for any particular shunt--and is one of its important parameters. For most substances, resistance is usually described in "ohms", however for some reason shunts are described by the voltage drop that occurs with a certain current: for example: "50 millivolts at 500 amperes." However the meter only cares about the ratio-which is the resistance--so a 500Amp/50 millivolt shunt is equivalent, from the TriMetric's view, to a 250Amp/25 millivolt shunt. They both have a resistance of 0.1 milliohm, or one ten thousandth of an ohm.

Setting up the TriMetric for the Correct Shunt

Shunt Cable ConnectionThe TriMetric is designed to use either a 500 Amp/50 millivolt (0.1 milliohm) or 100 Amp/100 millivolt (1.0 milliohm) shunt. The latter shunt delivers 10 times the voltage for a given current flow through the shunt, so themeter can show an extra digit of current resolution (down to 0.01 amp) compared with the 500 Amp/50 millivolt shunt, which displays a minimum current of 0.1 amp. To make the TriMetric read "amps" and "amp-hours" correctly, you must tell the TriMetric which shunt is being used. This is done by programming either an "L" (low) or "H" (high) in one of the program modes. ("L" for the 100A/100 mV shunt, and "H" for the 500 A/50 mV shunt.) For how to do this refer to TriMetric instructions under "How to set efficiency factor and shunt type".

Bogart Engineering


Write a review

There are no reviews for this product.

Click here for BBB Business Review ASE NESEA Member
Paypal Visa MasterCard Amex Discover
McAfee SECURE sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams