Dankoff Suncentric 7426 DC Surface Pump

Dankoff
SunCentric
Solar Centrifugal Pumps

The Dankoff SunCentric uses solar-electric power to pump as much as 50,000 gallons (200 cu. m.) per day from shallow water sources.

Applications include irrigation, livestock, domestic water, pond management, water treatment, swimming pools, solar water heating, hydronic space heating, fire protection, and more. These pumps have been in worldwide use since 1989. They can be used without batteries. No electronic pump controller is required. Maximum suction lift is 10 vertical feet (3 m).

Customer Testimonials

"We are satisfied with the performance of the Dankoff pump. It runs cool and is noiseless. It has easy access for repair. The spring seals provided along with the pumps are also good. We have noted that the pump starts at 40-50% of rated input to the motor. We are glad to mention that the pumps shipped so far are receiving good review and acceptance."
--- Sairam Solar Systems, New Delhi, India

  "We have 1000 trees on drip irrigation. has been running for 5 years. It's an amazing pump. I love that it runs directly on solar with no controller or batteries."
-- A.P., SunCentric owner, Longmont, Colorado, USA

"Thank you very much for sending the SunCentric circulating pump. It is perfect. It starts first thing in the morning and there is absolutely no vibration or sound."
Application: PV-direct circulation of solar heated water through the floor of a 4000 sq. foot (404 sq. m.) building.
-- Bob Ramlow, Midwest Renewable Energy Association, Wisconsin USA

PV Array-Direct Application A PV-direct system uses water storage instead of batteries. This is the simplest and most reliable system, and is easy to transport. No electronic controls are required. A solar tracker (optional) will help to maintain optimum flow through the entire solar day. Storage of 3-7 days' water demand is recommended. Optimum for circulation of solar-heated water Battery Application A battery system is best where there is need for constant pressure or pressure on demand, or where a tank is not feasible, or where a battery system is required for other power applications. Batteries can be charged by any power source.

The SunCentric!" Solar Centrifugal Pump helps farmers in India

Reading the Charts

• Select the appropriate chart of "PV Array-Direct Applications" or "Battery Applications".
• Total Dynamic Head = Vertical distance from surface of the water source to the discharge or top of storage tank + pipe friction losses.
• Use solid line grid for English units. Use broken line grid for metric units.
• Locate the coordinates for the required head and flow.
• Find the pump curve that is nearest to that point.
• If there is more than one curve to chose from, compare the power requirements.
• For PV-Direct systems, array sizing (watts) is critical. DO NOT undersize the array.

SunCentric Pump Selection +

Suction Capacity

• Suction limit is 10 vertical feet (3 m) at sea level-subtract 1 foot for every 1000 ft. elevation (1 m per km).
• For best reliability, place the pump low and close to the water source to minimize or eliminate suction.

Pump Placement

• Place the pump close to the water source to minimize suction lift. This will minimize the possibility of cavitation which causes excessive wear and loss of
• performance.
• Horizontal position: Place outlet at the top. It can be rotated to face horizontally or vertically upward.
• Vertical position: Place motor on top.
• Pump must be sheltered from rain and direct sunlight.

Wire and Pipe Requirements

• Intake pipe: Pipe should be as direct and short as possible. Avoid any high point that can trap an air pocket.
• Refer to a pipe sizing chart (included with the pump instructions). Pipe may need to be larger than the pump ports. Undersized pipe will greatly decrease pump
• performance.
• Refer to a low voltage wire sizing chart. Size the wire for less than 3% voltage drop. Undersized wire will greatly decrease pump performance.

Dimensions, Pipe Fitting Sizes, Shipping Weight

Overcurrent Protection

• Fuse or circuit breaker is required.
• Ampere rating = amps at the pump + 15-25%
• Minimum DC voltage rating = volts at the pump X 2. (Type FRN fuses are rated 125V DC)

Maintenance

• No regular maintenance is required.
• Pump can be repaired in the field using ordinary tools and skills, without removing the pipes.
• Instruction manual shows illustrated repair details.
• Motor brushes: Typical brush life peak hours = working voltage X 800 / 3rd digit of model number. EXAMPLE: PV-Direct curve #60 is Model 7526 working at
• 30V. Typical brush life = 30 X 800 / 2 = 12,000 peak hours. This represents about 5-8 years of service.
• Shaft seal has a very long life under normal conditions. Purchase spare seals if water is loaded with abrasive silt or if pump can possibly run dry.

Materials

• Pump body: cast iron, ASTM A48-76
• Impeller: glass filled polycarbonate
• Seal: carbon/ceramic, industry standard
• Temperature limit: 140°F (60°C)

High Temperature Option

• Temperature limit: 212°F (100°C)
• Impeller: brass
• Brass impeller reduces flow by approximately 15% (power is same)
• Make sure to request the HIGH TEMPERATURE version of the pump in the comments section of your order.

Accessories

• Foot Valve (required if pump is placed higher than water source)
• Float switches: please inquire

Spare Parts

• Seal & Gasket Kit: specify pump number, and if high temperature
• Motor Brush Kits: specify model number

Warranty

• Two years against defects in materials and workmanship.

*formerly 13xx and 25xx

**formerly 29xx