IronRidge Genesis Pro Gps-168" Modular Flushmount

A new breakthrough product in the PV industry, developed and tested by IronRidge.

• All Genesis PRO Series Flush Mounts are rated at 125 mph wind-loading (50 lbs/ft²)!
• Quick and easy top-down installation for installing plug-and-play modules allows the entire assembly to take place on the roof.
• Installation can occur on any type of roof; including composition shingles, tile or standing seam and can be used with standard roof flashing if desired.
• Our flush mount system may be mounted in any direction.
• All IronRidge products carry our Industry Leading 20-year Warranty.
• Fully engineered and tested, our Genesis PRO Series (GPS) meets and exceeds; UBC standards for wind loads and building code requirements.
• This system will accommodate any and all standard modules from every major solar manufacturer in the industry.
• Due to roof orientation or limited space, the PV modules may be mounted vertically or horizontally.

Innovative Channel Design Provides Strength and Mobility Genesis PRO Series (GPS) Flush Mounts are designed so that professional installers and even the not-so handy man can install a PV system quickly, safely and efficiently. Completely engineered and tested so as not to compromise quality, these mounts will resist the harshest weather conditions.
GPS Components Provide Strength and Added Degrees of Freedom Our press-fit GPS Foot Clamp Assembly provides a sturdy attachment point to any roof with the freedom of adjustability along the rails. This clamp style attachment is 20x stronger than similar sliding bolt styles! The installer is given the option of mounting the feet on the inside of the Panel Support Rails or the outside. The GPS Feet can be lagged to a roof, attached to a Sliding Foot Assembly for Spanish style roofs, or attached to Standoffs for pitched roofs.
The GPS Spacer adds overall stability yet requires only 1/4 inch in between panels as opposed to 1 inch required by other mount manufacturers! It too can be positioned anywhere along the GPS Panel Support Rails by sliding the bolt head along the channel. The Spacer clamps the panels into place so as not to load the module glass.
The GPS End Clamp completes the easy top-down installation while on the roof. Our GPS design alleviates the need to hoist the mount to the roof and provides the versatility to fasten modules of any length. This component is precisely fabricated to fit any PV module on the market. (Please specify what panels are being used on every GPS order.)
Sliding Foot Assembly Mounts Under Spanish Style Roofs The optional Sliding Foot Assembly (SFA) attaches to the foot of any GPS model and fastens under Spanish style roofs as shown. The installer is allowed to attach the SFA to any joist and rotate 360 degrees about the lag screw until the desired position is reached. The Spring Nut slides along the channel and locks into any position so that the stud will line up with the roof tile at the desired location. From here, the GPS Mount is attached to the stud without any interference. One SFA is required per GPS Foot.     The SFA allows the stud location to be in an area anywhere within 44 square inches!
	Stand-offs Add Tilt to a GPS System on a Pitched Roof Our Stand-offs work with any standard flashing such as the Oatey #11841* or equivalent “No caulk” Vent Stack Flashing. Stand-offs come in 3 and 6 inch lengths, and are powder coated for corrosion resistance. Your installation would benefit from: Quick and easy installation Fully engineered and tested products The ability to mount any solar panel An industry leading 20-year warranty!

To determine which mounting rack to order for your array, Download the following PDF documentation describing the Genesis Pro Series.  The sizing chart with Retail Prices listed is on the last page.  Don't hesitate calling us for asistance if you have any questions about which mount is right for you.

• Genesis Pro Series
• Genesis Pro Instructions

Important: You must specify the solar panel manufacturer, model, and quantity to insure correct components are included with each kit.

Splice Kit

• GPS model numbers are based on overall GPS Rail length. (i.e. GPS-084 consists of (2) 84” GPS Rails)
• Hardware or fasteners provided as required for the installation of the mount.
• *Kits have spliced rails for overall length.
• Rail lengths longer than 96 inches are supplied with two pieces that are spliced together at the installation site. Single piece rails are available by special order and are shipped by common carrier.
• All kits contain fully engineered and tested components. All items manufactured under the complete control of our Quality Assurance Guidelines by our in-house professionals.